品牌:RETZ瑞茨/我们一直致力于流体控制和测控领域的持续创新,始于2005……
进口玻璃管浮子、转子流量计产品用途 Product use
玻璃管转子流量计在垂直的透明锥管内,装有可上下移动的浮子(转子),当液体自下而上流经锥管时,被浮子节流,在浮子上下游之间产生差压,浮子在此差压作用下上升。当使浮子上升的力与浮子所受的重力,浮子及粘性力三者的合力相等时,浮子上进口玻璃管浮子、转子流量计2.jpg于平衡位置,因此流经流量计的流体流量与浮子的上升高度,亦即与流量计的流通面积之间存在着一定的比例关系,浮子的位置高度可作为流量量度
The
glass rotor flowmeter is installed in a vertical transparent co
进口玻璃管浮子、转子流量计主要特点 Main features
透明玻璃管,读数清晰可见 Transparent glass tube, clear and visible reading
低压力损失设计 Low pressure loss design
较宽的流量比10:1 Wide flow ratio 10:1
适用于腐蚀性液体的测量。耐腐能力强,可检测酸(氢氟酸除外)、碱、氧化剂和其它腐蚀性的气体或液体 Suitable for measuring corrosive liquids. Strong corrosion resistance, capable of detecting acids (excluding hydrofluoric acid), alkalis, oxidants, and other corrosive gases or liquids
进口玻璃管浮子、转子流量计技术参数 Technical parameter
产品型号 公 称通 径(mm) 流 量 范 围 工作压力
(MPa)
液体(L/h) 气体(m3/h)
RB-LZ4 Φ4 1~10 0.016~0.16 ≤1
1.6~16 0.025~0.25
2.5~25 0.04~0.4
RB-LZ6 Φ6 2.5~25 0.04~0.4
4~40 0.06~0.6
6~60 0.1~1
RB-LZ10 Φ10 6~60 0.1~1
10~100 0.16~1.6
16~160 0.25~2.5
RB-LZ15 Φ15 16~160 0.25~2.5 ≤0.6
25~250 0.4~4
40~400 0.6~6
RB-LZ25 Φ25 40~400 1~10
60~600 1.6~16
100~1000 2.5~25
RB-LZ40 Φ40 160~1600 4~40
250~2500 6~60
RB-LZ50 Φ50 400~4000 10~100 ≤0.4
600~6000 16~160
RB-LZ80 Φ80 1000~10000 50~250
1600~16000 80~400
RB-LZ100 Φ100 5000~25000 120~600
8000~40000 200~1000
二、安装和使用
1、安装
(1)仪表安装前应仔细检验玻璃管是否损坏,并将为防止浮子跳动的填充物取出、检查浮子能否自由上下滑动。
(2)流量计垂直安装在管道上(锥管大端向上),流向自下而上。安装流量计的管道系统应具有足够的钢度,安装时,应避免大力扭动流量计。
(3)为便于观察和维修,安装时应留有足够的空间。
(4)管路中如有倒流,特别是有水锤作用时,为防止流量计损坏,应在流量计下游阀门之后安装单向逆止阀。为便于检查、维修、更换流量计和清洗管路的需要,推荐按图五安装旁路管。
(5)当被测流体含有较大颗粒物质或较脏时,应在流量计上游安装过滤器。
(6)当被测流体为脉动流,造成浮子波动不能测量时,应在流量计上游安装适当尺寸的缓冲器或定值器以消除脉动。
(7)用于测量气体时,为了使仪表能稳定工作,流量计出口端的压力不应太低。流量计上游的阀门应全开,并用流量计下游的阀门来调节流